New Pots on ETSY!!!

It's been said that I can't just make the stuff...

I've gotta do something with it, right?

So check out my ETSY site, and let me mail you a wonderful handmade wood fired and salt glazed pot! I'll be adding more work over the weekend, so check back often!

After the tour...

Just a few images from the potters tour...

My friend Shana, trying her hand at turning on the

wheel, gets a lesson from me...

I had a great turnout, thanks to everyone

who stopped out at Brush Valley Pottery!

Post-firing Firing post...

It has been a few days since my last post so this one is going to be a long one...all about the salt firing I just finished monday morning at 3 a.m.! This was the 6th time I've fired the kiln here in Brush Valley and the 3rd time for mostly rawglazed pots. For some of you who aren't potters, this means that I glaze the work when it is leather hard, using slip glazes that have a large amount of clay in the batch recipes. The clay in the glaze allows the glaze to shrink with the pot as water evaporates during the drying process. It can be tricky and most people choose to bisque fire their work and then glaze, but out of necessity, with no electric/bisque kiln here in Brush Valley, and the fact that most of my work only needs a liner glaze, I use this process of once firing. Once the pots are dry, it's time to load and fire.

Mugs tumblers, soup bowls and plates, lidded jars

and pitchers.

The firebox extension worked out great

for preheating the greenware/rawglazed pots.

I loaded it up with large cherry and oak chunks,

clammed it up and went to bed around

4am. At 8 am I returned to find

coals still in the box and started the firing...

Without a Pyrometer to gauge the early

part of the drying process

I used this chimney

thermometer for a wood stove.

I need it for the beginning of the firing

to make sure nothng blows up at the point

where the water left in the pots

starts to "boil" or evaporate...

Toward the end of the firing we used the flame

to stoke off of and had a nice,

even firing of cone ten down.

Heres a picture of the kiln shed and flame coming

from the chimney. As soon as the flame went in, I

stoked again, and the flame lasted abut 1 1/2 minutes per

stoke. This temperature(nearly 2400 degrees) really ate up the wood!

I hope to post pics of the finished results soon! Dont forget about the potters tour! Can't wait to see you all here!

47 not 50

Well the Earthenware firing wasn't a complete disaster, but I've had better...The liner glaze acted up quite a bit, bubbling and looking either over fired or under fired in places...It may have been a thickness thing or the fact that I used it on greenware...Ron usually bisques everything. The planters and silverware strainers turned out great! Not enough salt in the kiln, either. So, next time I might just leave out the glaze ware and just do all planters...

For now, I'm speeding along to the next cone 1o firing, hopefully loading on Saturday and firing Sat night and Sunday. Sorry again, no pictures, but stay tuned as I'm taking plenty of pictures, I just can't upload them...I'm working on it! 

Well, back to the 47 mugs I have to put handles on...yeah, I know, 47? Why not 50?

I've got the recipes for Ron's liner glaze and clay body, so now I can run some color tests and get on with the firing!

Here's some more info for everyone-

Ron's Clay: Cone 04-5 (we tested this in a very fast gas kiln firing and it went to cone 10)

Newman Red: 80 lbs

Red Art: 25 lbs

Fire Clay: 10 lbs

Medium size Grog: 15 lbs

Neph Sy: 2 lbs

Transparent Glaze: cone 04-5

Frit 3124: 80Kaolin: 10

Flint: 10

Bentonite: 2

For Liner add to base 10% Zircopax

Last nite I got the Kiln all cleaned out and started to figure out where everything is going...I'm going to have plenty of room, but it will take some time to fit everything in...Sorry, no pictures this time!

Slipped and drying...

I finished decorating these planters this evening with white slip, a little colored slip, and then carving through to show the dark clay beneath.

I started the last 2 planters that I'll need

for the firing this morning. It was so nice

outside today, they were ready for the rims

this evening and I should have them finished tomorrow!

I even squeezed in a little triming on the

lane coming in from Luciusboro Road.

Seems like time is just flying by and

the Potters Tour is only a month away...

Woodfired Earthenware?

I've finally been in the studio after catching up on the outdoor chores...they say to make hay while the sun shines...so I've been making pots while the moon shines.

I'm almost ready to fire up the wood kiln with an earthenware salt glaze firing! I'll fire somwhere between 1800 to 2000 degrees...I was inspired to try this technique over the summer while helping Ron Meyers with his workshop at Penland. Ron fires a wood kiln down in Georgia to earthenware temps. I think there are some subtle colors that will show up nicely in this temperature range.
During second session at Penland, I worked with Ayumie Horie who also uses earthenware. I loved her clay body and brought some home with me. I've taken to combining Ayumie and Ron Meyers clay together, about half and half, both of which were mixed by Highwater Clays in Asheville, NC, and using this mix to make the large planters shown above. The planters shown above were made using Daniel Johnstons Thai style construction technique. They'll be stacked rim to rim in the kiln. The sizes range from 12 inches in height to 18 inches across the top rims. These are some of the largest pots I've made...

I'm making a few cups and some other functional pieces and hope to test some glazes and slips in this firing. I ought to be ready to fire sometime soon! I am really excited to try something new! It keeps things fresh!

If you're interested in helping or just seeing the wood fire process, just let me know!

Here are a few recipes I'll be using for this firing...Thank you Ayumi
Modified Clay c/02 ---3 o’clock
OM 4 Ball Clay 10
Redart               70
Goldart              20
Frit 3124             3
Barium                0.25
Bent                    2
Kyanite (fine)      5

White Slip c/02
OM4 Ball Clay   36.1
EPK                   18.1
Neph Sy               3.8
Frit 3124            25.8
Zircopax             13.8
Buttercup #6406   1.4
Gray #6572          0.24
I'll post Ron's clay body and liner glaze as soon as I find it...